Hi,欢迎访问北京北广精仪仪器设备有限公司

北京北广精仪仪器设备有限公司

柏乡塑料磨擦磨损试验机厂家

联系我们
  • 北京北广精仪仪器设备有限公司
  • 陈丹
联系方式
北京北广精仪仪器设备有限公司
  • 联 系 人:陈丹
  • 手 机 号:
  • 公司电话:
  • 公司地址:北京
文章详情

柏乡塑料磨擦磨损试验机厂家

发布用户:Bgjy 时间:2021-11-26 10:26

柏乡塑料磨擦磨损试验机厂家

柏乡塑料磨擦磨损试验机厂家


产品名称:塑料滑动摩擦磨损试验机

型号:M-200 特点:本机采用高精度扭矩传感器,嵌入式中央单元处理系统cpu控制,支持xp  win7. win8.  win10系统,软件实时绘制显示扭矩-时间曲线、摩擦系数-时间曲线,绘制摩擦力、摩擦系数、磨损量等曲线变化,可设定试验次数,显示当前试验次数,设定时间及当前试验时间等多种功能;

本机具有一次设置,全自动运行,实验结束后自动停机,并检测磨损程度;

配有彩色打印机,可以打印出带有曲线,表格数据,试验单位名称等精美的试验报告单。另外本仪器配有故障自动报警系统问题报警灯和软件报警灯同时提示出现问题时间保护仪器以免零件损坏。是各个科研单位,大学,企业实验室的必备检测设备。

柏乡塑料磨擦磨损试验机厂家

试验负荷;E. test load;

使用说明书一份;One copy of the instructions;

摩擦力矩: 0--4N·m ±0.5%

试验设备test equipment

主要技术指标:

设置:对试验的参数进行设置,如试验速度,试验数据等。 开始:开始进行试验。

试验中上转轴保持静止,下转轴以200转/分转动,摩擦副做滑动摩擦,对磨2小时,负荷20公斤,根据材料,允许选择其它负荷.试验环境温度为23±5摄氏度.During the test, the upper shaft remains stationary, the lower shaft rotates at 200 rpm, and the friction pair is subject to sliding friction. For 2 hours, the load is 20kg. Other loads are allowed according to the materials. The test environment temperature is 23 ± 5 ℃.

停止:停止试验,试验结束。打印:打印试验报告。

系统运行稳定,可靠性高。The system runs steadily and has high reliability.

摩擦力矩: 0—4N.m;friction torque: 0 - 4N.m;

柏乡塑料磨擦磨损试验机厂家

试验报告Test report

复合材料滑动摩擦磨损试验机   本机采用高精度扭矩传感器,16 位单片机电子处理系统,使得本仪器各项测试指标精度非常高。由于集成程度很高,所以设备本身的稳定性极好,本机具有一次设置,全自动运行,实验结束后自动停机,并检测磨损程度,同时通过打印机打印试验数据等功能。是各个科研单位,大学,企业实验室的必备检测设备。

试验报告Test report

加载系统,对试样和圆环,可施加法向力,精确到5%以内。Loading system, for the sample and the ring, the additional force can be applied, accurate to within 5%.

供电电源 (鸿海)

砝码重量:4KG 砝码十件,1KG 砝码十件,可实现重量叠加功能;weight weight: 4KG weight ten, 1KG weight ten, can achieve weight superition function.

高精度扭矩传感器一只(固尔)

管理:可对使用些设备的用户进行管理。退出:退出操作系统。

计 数 器: 0-9999小时

本试验中圆环的材质对塑料磨损试验结果影响很大,因此本标准采用的圆环,其外形尺寸见The material of the ring in this test has a great influence on the plastic wear test results. Therefore, the ring adopted in this standard has the dimensions shown in Figure 材料为45号钢,圆环要求整体淬火,热处理HRC 40~外圆表面光洁度▽倒角处均为0.5×45度,外圆表面与内圆同心度偏差小于0.he material is 45 steel, the ring is required to be quenched as a whole, the heat treatment is HRC 40- the surface finish of the outer circle is ▽ the chamfering is 0.5 × 45 degree, and the concentricity deviation between the outer circle surface and the inner circle is less than 0.    圆环可以反复使用,每次试验后,需重新磨削。当外径小于36毫米就不能再用。作仲裁试验时用直径40毫米的圆环。The ring can be used repeatedly. After each test, it needs to be grinded again. When the outer diameter is less than 36 mm, it can not be reused. A ring with a diameter of 40 mm must be used for the arbitration test.

柏乡塑料磨擦磨损试验机厂家

试验中上转轴保持静止,下转轴以200转/分转动,摩擦副做滑动摩擦,对磨2小时,负荷20公斤,根据材料,允许选择其它负荷.试验环境温度为23±5摄氏度.During the test, the upper shaft remains stationary, the lower shaft rotates at 200 rpm, and the friction pair is subject to sliding friction. For 2 hours, the load is 20kg. Other loads are allowed according to the materials. The test environment temperature is 23 ± 5 ℃.

本试验中圆环的材质对塑料磨损试验结果影响很大,因此本标准采用的圆环,其外形尺寸见The material of the ring in this test has a great influence on the plastic wear test results. Therefore, the ring adopted in this standard has the dimensions shown in Figure 材料为45号钢,圆环要求整体淬火,热处理HRC 40~外圆表面光洁度▽倒角处均为0.5×45度,外圆表面与内圆同心度偏差小于0.he material is 45 steel, the ring is required to be quenched as a whole, the heat treatment is HRC 40- the surface finish of the outer circle is ▽ the chamfering is 0.5 × 45 degree, and the concentricity deviation between the outer circle surface and the inner circle is less than 0.    圆环可以反复使用,每次试验后,需重新磨削。当外径小于36毫米就不能再用。作仲裁试验时用直径40毫米的圆环。The ring can be used repeatedly. After each test, it needs to be grinded again. When the outer diameter is less than 36 mm, it can not be reused. A ring with a diameter of 40 mm must be used for the arbitration test.

精度:速度精度:1%

注:试验设备本标准推荐采用M-200型磨损试验机。Note: M-200 wear testing machine is recommended in this standard.

适用范围:适用于塑料制品、橡胶制品、石墨板材或其他复合材料的滑动摩擦,磨损性能测试,也可对试验中试样的磨擦力、磨擦系数和磨损量进行测定。也可对试验中试样的磨擦力、磨擦系数和磨损量进行测定。

本试验中圆环的材质对塑料磨损试验结果影响很大,因此本标准采用的圆环,其外形尺寸见The material of the ring in this test has a great influence on the plastic wear test results. Therefore, the ring adopted in this standard has the dimensions shown in Figure 材料为45号钢,圆环要求整体淬火,热处理HRC 40~外圆表面光洁度▽倒角处均为0.5×45度,外圆表面与内圆同心度偏差小于0.he material is 45 steel, the ring is required to be quenched as a whole, the heat treatment is HRC 40- the surface finish of the outer circle is ▽ the chamfering is 0.5 × 45 degree, and the concentricity deviation between the outer circle surface and the inner circle is less than 0.    圆环可以反复使用,每次试验后,需重新磨削。当外径小于36毫米就不能再用。作仲裁试验时用直径40毫米的圆环。The ring can be used repeatedly. After each test, it needs to be grinded again. When the outer diameter is less than 36 mm, it can not be reused. A ring with a diameter of 40 mm must be used for the arbitration test.

试样的制备方法,摩擦表面状况,测定的试样个数;B. pparation method of sample, friction surface condition, number of samples measured;

注:试验设备本标准推荐采用M-200型磨损试验机。Note: M-200 wear testing machine is recommended in this standard.

试样尺寸: 30mm*7mm*6mm±0.1 mm

此界面可以设置报告名称,试验参数,可以通过勾选参数前边的“对”勾,来决定试验报告中是否打印此项(数据项相同),可能通过勾选“对”勾来确定是否打印,试验参数,试验数据,试验曲线,试验备注等信息。选择完后可通过打印,预览报告,如果满意可以在预览界面通过打印,打出报告。

柏乡塑料磨擦磨损试验机厂家

结构紧凑,使用方便,简单。The structure is compact, easy to use and simple.

复合材料滑动摩擦磨损试验机  技术参数Technical parameters:  M-200

采用高精度电机、驱动机、传感器,精度高。using high pcision motor, drive and sensor, high accuracy.

复合材料滑动摩擦磨损试验机   本机采用高精度扭矩传感器,16 位单片机电子处理系统,使得本仪器各项测试指标精度非常高。由于集成程度很高,所以设备本身的稳定性极好,本机具有一次设置,全自动运行,实验结束后自动停机,并检测磨损程度,同时通过打印机打印试验数据等功能。是各个科研单位,大学,企业实验室的必备检测设备。

计数器精度:1S

管理:可对使用些设备的用户进行管理。退出:退出操作系统。

供电电源 (鸿海)

传动系统,用来带动圆环以给定的转速旋转,精确到5%以内,并要求圆环安装部位轴的径向跳动小于0.01毫米。The transmission system is used to drive the ring to rotate at a given speed, accurate to within 5%, and the radial runout of the shaft at the installation ition of the ring is required to be less than 0.01mm.

精度:速度精度:1%

记录圆环转数的计数器或记时器,精确到1%以内。A counter or chronograph for recording the revolution of a ring, with an accuracy of less than 1%.

柏乡塑料磨擦磨损试验机厂家

数据采集系统 (北京北广)

精度:速度精度≤1%;负荷精度≤0.5%;摩擦力矩精度≤1%;计数器精度≤1S;传感器测量精度≤1accuracy: speed accuracy is less than 1%; load accuracy is less than 0.5%; friction torque accuracy is less than 1%; counter accuracy is less than 1S; sensor measurement accuracy is less than 1%F.

负 荷: 196N ± 0.2%(可扩充到392N)

记录圆环转数的计数器或记时器,精确到1%以内。A counter or chronograph for recording the revolution of a ring, with an accuracy of less than 1%.

试验结果:磨痕宽度或体积磨损及摩擦系数的测定结果;F. test results: test results of wear mark width or volume wear and friction coefficient;

记录圆环转数的计数器或记时器,精确到1%以内。A counter or chronograph for recording the revolution of a ring, with an accuracy of less than 1%.

计数器精度:1S

计算机控制系统一套;A set of computer control systems;

传感器测量精度:1% FS

可以通过此界面管理使用此设备的人员信息,可以创建用户,删除用户,查看用户密码(对管理员),修改用户密码。

柏乡塑料磨擦磨损试验机厂家

试验结果:磨痕宽度或体积磨损及摩擦系数的测定结果;F. test results: test results of wear mark width or volume wear and friction coefficient;

电源线:接入电源线插口

采用高精度电机、驱动机、传感器,精度高。using high pcision motor, drive and sensor, high accuracy.

摩擦力矩: 0—4N.m;friction torque: 0 - 4N.m;

控制系统一套(北京北广)

控制线:一头接设备,一头接电脑上边串口复合材料滑动摩擦磨损试验机 本仪器融合了当前 的智能电路系统进行控制,并结合老式M-200摩擦磨损试验机的功能进行改造而成,本仪器具有测控精度高,操作便捷等优势,是科研院所、质检机构、实验室研究的试验设备。

负荷精度:0.5%

标准摩擦环二件;Two standard friction rings;

摩擦力矩: 0--4N·m ±0.5%

接线说明

砝码重量:4KG砝码一件,1KG砝码4件,可实现重量叠加功能。

打开:可以打开以前保存的文件,重新获得数据,打印报告。

柏乡塑料磨擦磨损试验机厂家

试验报告Test report

打开:可以打开以前保存的文件,重新获得数据,打印报告。

供电电源 (鸿海)

停止:停止试验,试验结束。打印:打印试验报告。

试验报告可打印试验参数,试验数据,曲线,备注等信息,简单,方便,可编辑。The test report can print experimental parameters, test data, curves, remarks and other information. It is simple, convenient and editable.

计算机数据采集卡一块;A piece of computer data acquisition card;

系统运行稳定,可靠性高。The system runs steadily and has high reliability.

测定和记录摩擦力矩系统,精确到5%以内。Measure and record the friction torque system to within 5%.

圆环材质、硬度、光洁度和外径尺寸;D. ring material, hardness, finish and outer diameter;

高精度扭矩传感器一只;High pcision torque sensor one;

柏乡塑料磨擦磨损试验机厂家